for further information contact your local stmicroelectronics sales office. may 2013 doc id 23730 rev 2 1/8 8 STDP2500 mobility displayport (mydp) to dp converter data brief features mobility displayport? (mydp) receiver ? link rate hbr2/hbr/rbr ?1 lane ? aux_hpd single-ended ac coupled signal, 1 mbps ? supports edp operation displayport transmitter ? dp 1.2a compliant ? link rate hbr2/hbr/rbr ? 1, 2, or 4 lanes ? aux ch 1 mbps ?hpd monitoring hdcp repeater with embedded keys aux_hpd translator to standard dp aux ch and hpd spread spectrum for emi reduction bandwidth ? video resolution up to 1920 x 1080 @ 60 hz, 24 bits per color ? audio 7.1 ch up to 192 khz sample rate low power operation ? powered from mydp source or from dp sink package ? 81 tfbga (5 x 5 mm) power supply voltages ? 3.3 v i/o; 1.2 v core applications audio-video accessory (dongle) for smart phones/tablets dp output 4 lanes mydp input clock generation ocm, spi aux ch & hpd handler i2c slave video format converter image capture displayport transmitter displayport receiver aux_ch aux_hpd main lane hpd www.st.com
description STDP2500 2/8 doc id 23730 rev 2 1 description the STDP2500 is a mobility displayport to stan dard displayport converter that facilitates streaming fhd 60 hz video and audio from mydp enabled smart phones and tablets to monitors and tvs with displayport 1.2a compliant inputs. the STDP2500 is a vesa mobility displayport (mydp) standard comp liant device, implementing a single lane displayport receiver and aux_hpd. the output port comprises a standard displayport 1.2a compliant transmitter with four main lanes, aux channel, and hpd signal. the mydp standard is a digital audio-vide o interconnect based on the v esa displayport standard for a mobile source device capable of streaming uncompressed audio and video. it uses the existing standard 5-pin connector commonly used for charging the portable mobile devices to stream the audio-video to an external display. the STDP2500 uses st?s latest generation displayport receiver technology that supports single av stream at hbr2 speed, a data rate of 5.4 gbps per lane. the displayport output in STDP2500 is a four lane differential output capable of operating either at hbr2, hbr or rbr data rate. this device can convert audio-video stream received from a mydp source on a single lane input at hbr2 data rate (5.4 gbps) into two lanes output at hbr rate (2.7 gbps) or four lane output at rbr rate (1.62 gbps). it can deliver 1080p 60 hz video with a color depth of 24 bits per pixel and audio up to 8 channels at 192 kb sample rate from a mydp source to displayport1.1a based monitors. displayport1.2a compliant monitors are capable of receiving mydp inpu t directly through a passive ca ble. STDP2500 complies with hdcp 1.3 content protection scheme with an embedded key option for secure transmission of premium digital av content. it can also act as hdcp repeater for the downstream sink when used in a do ngle application. the aux_hpd is a single-ended sideband channel that assists in low speed data exchange between the mydp source and STDP2500. the aux_hpd message handling is mapped to the corresponding aux channel message and hpd signal at the output port for the downstream sink. the aux_hpd data transfer rate is 1 mbps which is adequate for handling i2c and ir protocols. the mydp sour ce also uses the aux_hpd channel for the dpcd read-write access. this device has an on-chip microcontroller with an optional spi and i2c host interface for system configuration purpose. the STDP2500 im plements a sink detection and monitoring feature that automatically puts the device into low power operation whenever the sink is disconnected. an STDP2500 based accessory (dongle) is powered from the downstream sink. in addition, displayport1.2a compliant sinks in general are capable of charging the mobile source.
STDP2500 application overview doc id 23730 rev 2 3/8 2 application overview figure 1. STDP2500 in mobile accessory (dongle) application ape mydp tx video control usb mobile device STDP2500 27 mhz crystal dp1.1a / dp1.2a monitor dp 1 main lane hbr2 dongle aux_hpd dp 4 lanes, hbr/rbr hpd aux ch power uusb dp
feature attributes STDP2500 4/8 doc id 23730 rev 2 3 feature attributes 3.1 input interface mobility displayport main link configuration (sst format only) ? hbr2/hbr/rbr link rate ? 1 lane aux_hpd: 1 mbps manchester transaction format ?i2c over aux_hpd ? ir over aux_hpd pixel bit depth: 24 bpp, 18 bpp color format: rgb audio: up to 192 kb samples/sec, 8 ch/sample, 24 bits/ch 3.2 output interface standard displayport 1.2a compliant main link configuration (sst format only) ? hbr2/hbr/rbr link rate ? 4 lanes aux_ch: 1 mbps manchester transaction format ?i2c over aux ?ir over aux hpd: irq_hpd monitoring pixel bit depth: 24 bpp, 18 bpp color format: rgb audio: up to 192 kb samples/sec, 8 ch/sample, 24 bits/ch 3.3 supported video timings 1920 x 1080 (fhd) 60 hz: 24 bits/pixel 1920 x 1080 (fhd) 30 hz stereo 3d 3.4 supported audio timings up to 8-ch lpcm; word length up to 64 x fs; bit depth up to 32 bits, sample rate up to 192 khz 3.5 control channel interfaces aux_hpd, i2c host interface, spi and uart (uart for test/debug purposes only)
STDP2500 feature attributes doc id 23730 rev 2 5/8 3.6 hdcp 1.3 support key sets for dprx and dptx integrated in one-time programmable rom (otp) standalone hdcp repeater capability 3.7 package 81 tfbga (5 x 5 mm), 0.5 ball pitch 3.8 power supply voltages 3.3 v i/o; 1.2 v core 3.9 esd 2 kv hbm, 500 v cdm
ordering information STDP2500 6/8 doc id 23730 rev 2 4 ordering information 4.1 ecopack ? in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. table 1. order codes part number description STDP2500-ac 81 bga (5 x 5 mm) delivered in trays STDP2500-act 81 bga (5 x 5 mm) delivered in tape and reel
STDP2500 revision history doc id 23730 rev 2 7/8 5 revision history table 2. document revision history date revision changes 05-oct-2012 1 initial release. 28-may-2012 2 updated ordering information section.
STDP2500 8/8 doc id 23730 rev 2 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not authorized for use in weapons. nor are st products designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america
|
